How To Drain Gas From MTD Snowblower (All Models)

MTD snow blowers are a great way to keep your driveway and sidewalks clear of snow. But if your snow blower has been sitting for a while and you need to drain the gas, here’s what you need to do.

Why draining the gas out of the MTD snowblower is good before storing?

Draining the gas out of the MTD snowblower is good before storing it for next season. You can prevent the carburetor from getting gummed up and it will also extend the life of the snowblower.

Additionally, this will help to prevent any ice from forming in the snowblower’s fuel lines. Draining the gas out of your gas-powered snow blower is a simple process that only takes a few minutes.

How To Drain Gas From MTD Snowblower

Method # 1 – Let it Run Until Fuel Tank Is Empty

The easiest way to drain the gasoline in your snowblower is to go ahead and start it and just let it run.

But this method is feasible and cost-effective only if you have very little gas in your fuel tank.

Eventually, the snowblower is gonna run out of gas and stop.

If you want more precision, remove your MTD snowblower carburetor to drain out residual gas from the carb too.

Method # 2 – Extract Gas From Fuel Line

It is an easy method to drain the gas out of the tank especially if you have a lot left in it.

  • In MTD snowblower engines, the gas tank has a fuel line coming directly out of its bottom.
  • There is a retaining clip on the line to tighten it.
  • Take up a pair of pliers and just remove that retaining clip or slide that down the fuel line.
  • Now go ahead and loosen up this fuel line.
  • Make sure you have something underneath to catch all the gas that’s going to drain out.
  • You can tilt your snowblower on one side to extract the remaining gas.
  • And once all the gas is drained out of your machine make sure you replace that fuel line and retaining clip.
  • Start the MTD snowblower engine and let it run. It will shut off on its own when out of gas completely.

Method # 3 – Using a Siphon Pump

If you want to drain the gas from your MTD snowblower, you can do so by using a siphon pump. This is a more quick and easy way to get the job done and you won’t have to worry about spilling gas all over the place.

Here’s how to siphon gas from the MTD¬†snowblower

  • Make sure that your snowblower is at an even level, turned off and the engine is cool.
  • Place an empty container to catch the residual gas near your snowblower.
  • Open or unscrew the fuel tank cap.
  • Take the siphon pump and place the intake tube into the gas tank.
  • Then put the other end of the tube into the container.
  • Squeeze the siphon pump with your hand until the gas tank is empty.
  • This procedure has its limitations so not all the gas from the snow blower is extracted.
  • To completely empty the gas tank, start the MTD snowblower engine and let it run. It will shut off on its own when out of gas.

Do You Need to Drain MTD Snowblower?

If you are a newbie using an MTD snowblower, you must know that it’s important to drain the gas and oil from your snowblower before storing it for the summer. This is because gas and oil can deteriorate over time, and if they’re left in the snowblower, they can cause damage to the engine and parts.

Precautions To Take Before Draining Gas From MTD Snowblower

Before you begin the process of draining the gas out of your snowblower, there are a few safety measures you should take.

  1. Make sure that the snowblower is turned off and that the engine is cool.
  2. Disconnect the spark plug wire from the spark plug. This will prevent the engine from accidentally starting while you are working on it.
  3. Make sure that the MTD snowblower is in a well-ventilated area. It will allow any fumes that are present to dissipate quickly.
  4. Wear gloves and eye protection while you are working to protect yourself from any potential injuries.
  5. Finally, make sure that you have a clean container to catch the gas as you drain it out.

Related Questions – How To Drain Gas From MTD Snowblower

How do I drain the gas from my snowblower carburetor?

If your snowblower is having trouble starting, it may be due to old or dirty gas in the carburetor. Draining the gas from your snowblower’s carburetor is a simple process that anyone can do.

To drain the gas from your snowblower carburetor,

  1. Disconnect the spark plug wire from the spark plug. This will prevent the engine from accidentally starting while you’re working on it.
  2. Next, locate the carburetor. On most snowblowers, it’s located near the bottom of the engine.
  3. Once you’ve found the carburetor, you’ll see a small drain plug near the bottom. Remove this plug and allow the gas to drain out.
  4. Once the gas is drained, replace the drain plug and reconnect the spark plug wire.

Following these simple steps will help prolong the life of your snowblower and ensure that it’s ready to go.

Related Articles:

MTD Snowblower Only Runs On Choke

MTD Snowblower Drive Problems – Easy Fixes To Help You Get Moving

Leave a Comment