How To Clean BILT HARD Snowblower Carburetor

How To Clean BILT HARD Snowblower Carburetor. The carb is responsible for mixing the fuel and air in the right proportions and delivering it to the snowblower engine. If the carburetor of your BILT HARD Snow thrower is not working properly, its engine will not run properly. Or maybe you will have to run your snowblower on choke only.

There are a few things you can do to try to fix a snow blower carburetor.

First, you can clean the carburetor by just spraying a carb cleaner in all its openings without removing it. This is usually all that is needed to fix the issue.

If that doesn’t work, you may need to disassemble the carburetor and clean it thoroughly.

Rebuilding a carburetor is not as difficult as it may sound. You can do it yourself with a few tools and a little patience.

Keep reading for a step-by-step guide on how to clean a BILT HARD snowblower carburetor after removing it as well as get the tips only a pro can tell. No matter how much your carburetor is gummed up, you can fix it with these simple steps.

Can you clean the BILT HARD carburetor without removing it?

Although it is possible to clean a carburetor without removing it, it is generally not recommended. Removing the carburetor allows for a more thorough cleaning and inspection, and it also allows you to make any necessary repairs.

How To Clean BILT HARD Snowblower Carburetor Thoroughly

In this step-by-step guide to cleaning the BILT HARD snow thrower carburetor, we have divided it into 4 major sections.

  1. Removing the Carburetor from the snow blower
  2. Disassembling / Opening the Carburetor
  3. Cleaning the BILT HARD Snowblower Carburetor
  4. Reassembling / Reinstalling 

You will require the following items to rebuild the carb:

  • A wrench
  • High-Quality Carb Cleaner
  • Pliers
  • Dry Cotton Cloth

1. Removing the Carburetor from the BILT HARD Snow blower

Follow these steps carefully to revive your carb and of course snow blower:

Remove the Cover

Unscrew all 6 bolts with a socket wrench and set the cover aside attached to the exhaust guard.

Remove the Fuel line

First, Turn off the fuel supply or clamp the BILT HARD snow thrower’s fuel line with the fuel line clamp.

Now slide the clip on the fuel line up and pull the line away from the carb.

Pull Off the Primer line

Pull the primer line away from the carburetor after removing its clip.

Removing the Throttle Cable

To fully remove the carburetor, you must first remove its throttle cable.  Slide the carb a little bit away from the body. Now slide the throttle inside and pop up the throttle cable to release it.

Now we are going to the next phase of disassembling our BILT HARD Snowblower’s carburetor.

2. Disassembling BILT HARD Snow Thrower Carburetor

Remove the Gaskets

Peel off the gaskets from both ends of the carburetor using your fingers.

Empty the Carburetor Bowl

If you don’t want any fuel in your workspace then empty the carburetor completely, before tearing it apart. Pull off the bolt(mentioned in the picture below) to drain the fuel from the carburetor bowl or its base. Collect the fuel in any empty container.

Clean the exterior of the carburetor

Spray some carb cleaner all over your BILT HARD carburetor to clean its exterior. This way any dirt or grime on the outside will never get inside once you will open the carburetor.

Remove the Carb Bowl

Open the Carburetor bowl by removing the other bolt in the bowl. Remove any remaining fuel in it.

Release the Float

Slide the hinge pin with your fingers or pliers to remove the float. Set the pin and the float aside.

Note: Never spray carburetor cleaner on the float with the float needle on it. The float needle has a rubber seal that can be damaged by the chemicals in the carb cleaner.

Remove Main Jet

Take a flathead screwdriver and remove the main jet from the center or ‘neck’.

Remember that always use good quality flat-head screwdriver to unscrew the main jet. This is because main jet is made from soft metal and you can easily damage it with a slight wrong move.

Remove the emulsion tube

After removing the main jet, push the emulsion tube out of the ‘neck’ by inserting a flat-head screwdriver into the carb venturi.

Remove the O-ring

Finally, remove the O ring that seals the fuel bowl.

Note: Never spray carburetor cleaner on the o-rings. The o-rings are rubber seals that can be damaged by the chemicals in the carb cleaner.

3. Cleaning the BILT HARD Snow blower Carburetor 

It’s time to clean the BILT HARD carburetor thoroughly inside out to remove any accumulated dirt or fuel residuals.

Spray each passage/opening of the carburetor

Spray in each and every big or small opening of the carburetor with a good quality carb cleaner to get rid of dirt, grime, and other residuals.

Always place a container below before spraying the carb cleaner.

Spray The Main Jet

The most important part of the BILT HARD snowblower’s carburetor is its main jet. There is a tiny hole in it that is responsible to let the fuel go into the engine. If this got blocked the engine will run lean and creates problem in starting.

Most of the time it got clogged up or blocked, so we have to do this exercise. Spray it again and again until the hole is cleared of dirt or any blockage.

Other components of the Carb 

Spray the emulsion tube, and bowl. These are the other important parts of a carburetor that must be cleaned thoroughly before they can be reassembled. Spray carb cleaner at each of these parts well enough so that the carburetor can be used for a long time again.

Use a soft brush or a toothbrush 

Rub all the parts with a toothbrush or other small soft brush to further clean the carb.

Note: Don’t use a wired brush or any hard brush on the internal parts of the carburetor. It can damage them and affect the efficiency of the engine.

If you want, re-spray each part again after brushing.

Dry With A Clean Cloth

Now dry each component with a soft and clean cloth.

Reassembling the Carburetor

Set the emulsion tube

Put the emulsion tube back into its place by just sliding it with the screwdriver.

Place the Main jet

Reinstall the main jet after the emulsion tube and tighten it with the same screwdriver.

Reinstall the Float

Secure the float by inserting the hinge pin.

Put the O-ring

Reinstall the o-ring by simply pushing it with your hand on the edge of the fuel bowl.

Reassemble the fuel bowl 

Place the fuel bowl onto the carb body and tighten it with the wrench.

Put the Gaskets back on 

Now reattach bother gaskets on both sides of the carburetor.

Attach with the Engine

Slide the carburetor back onto the mounting bolts.

Attach Throttle Cable

To attach the throttle cable, push the throttle towards you and slide the cable into it. Now release the throttle.

Reinstall the Fuel line and Primer Line

Finally, attach the primer line and the fuel line to their place. Now you can switch on the fuel supply.

Attach the cover

Attach the cover and tighten all 6 screws to complete the cleaning.

Check BILT HARD Snowblower Air Filter

Always remember to check that the snowblower air filter is clean before starting up its engine. This will allow clean air to enter the carburetor because dirty air from the snow thrower air filter will reverse the progress you just made.

Related Questions – How To Clean BILT HARD Snow Thrower Carburetor

How do I make my snowblower go forward?

There are a few things you need to check if your snowblower is not going forward.

  • Make sure that the transmission is in the correct position. If the transmission is in the wrong position, the snowblower will not move.
  • Check the skid shoes. The skid shoes are what make contact with the ground and help the snowblower move. If the skid shoes are worn down, they will not be able to provide enough traction to move the snowblower forward.
  • And check the auger belt. The auger belt is what powers the blades that help move the snow. If the belt is worn or broken, it will need to be replaced.

How do you fix a snowblower that won’t shift gears?

If your snowblower won’t shift gears, there are a few things you can try to fix the problem.

  • The first thing you should check is the snowblower’s auger. If the auger is frozen or jammed, it can prevent the snowblower from shifting gears.
  • Another possible cause is a damaged or broken shifter cable. The shifter is what allows you to change gears. If the shifter is damaged, it will need to be replaced.
  • Check to see if the problem is with the transmission and gearbox. The transmission is what allows the snowblower to change gears. If the transmission is damaged, you will need to take the snowblower to a qualified repair shop.

BILT HARD Snow Blower Gas Powered Self Propelled with 212cc Engine

bilt-hard-snowblower-self-propelled

The 24-inch Gas Powered BILT HARD Snow Blower is a powerful and reliable snow blower that is perfect for clearing snow from driveways and sidewalks.

This snow blower has a two-stage design that allows it to clear snow down to the pavement, as well as an electric start that makes it easy to get started on clearing snow.

The LED light on this snow blower is also a great feature, as it allows you to see in the night easily while you are clearing snow.

With its 10″ serrated steel augers and 10″ impeller, the BILT HARD Snow Blower can move up to 500 lbs of snow per minute, making it ideal for clearing large areas quickly.

How To Clean BILT HARD Snowblower Carburetor – Conclusion

That was how easy to clean the BILT HARD Snowblower carburetor. A clean carburetor is essential for proper engine operation, and it also helps in improving fuel economy. So be sure to add BILT HARD snow thrower’s carburetor cleaning to your regular maintenance routine at the end of the season.

Related Articles:

 

Leave a Comment